1975 Chevy 4x4 Crate Engine HO 350 Cold Air Lifted 39 Swampers 4.88 Posi T400

Chevrolet C/K Pickup 2500 1975 Description

CONTACT PHONE NUMBER:
909-510-1167

THE TRUCK:

This is a complete rebuild and a "proven" heavy duty, igh performance off road trail & mud truck and trailer hauler.

It is built right and does not break parts and is Super Reliable.

I drove it here to Tennessee from California while pulling a "loaded" 30 foot trailer behind it with no problem - 2300 miles.

Plus it drives straight and smooth on the street with cold air and a nice stereo.

Every body gives you a "thumbs up" and a smile everywhere you go.

PRICE:
for sale $23,000 or trade for stock crew cab 4x4

MONEY SPENT:
I have spent over $30,000 on parts and supplies for this build,
That is separate from the cost of the complete rust free truck I started with.
And I have countless hours fabricating the truck for 2 years on jack stands.

LIFT:
About 17 inch lift
Tires are 39.5 tall.

a little bit taller than any truck you pull up next to.

CONDITION:
New everything - completely rebuilt.

PAINT:
New PPG paint with new front grill, ights, umper mirrors, oles filled, rip rails removed and so much more. The front end comes from a 1986.

MILES:
Has about 18,000 miles on the entire build: new crate motor, ustom built trans, ebuilt transfer case, ew custom drive-shafts, ustom cross over steering set up and complete axle builds and brakes. The paint was just applied this month with all new glass, ubber seals, indow motors etc..
Means Nothing: The cab odometer says 64,000 and I assume that it is 164,000, nly rolled over ounce. This truck was sitting for many many years. Mostly sits now too, have had it for 10 years.

PARTS LIST AND DETAILED DESCRIPTION:

ENGINE:
Has a NEW crate engine DIRECTLY from GM Performance Parts Catalog: HO 350, 3900 alone.
off road truck avenger carb by Holley $500
Phenolic spacer and long studs $50
Holley High Volume fuel pump and fuel lines, arge filter with AN fittings $250
MSD ignition Cap and Coil and rotor with 6al box and MSD wires and looms $400
Accel distributor $150
K&N 6 inch tall air filter and oil breathers $150
Crane Vortec 1.6 roller rockers $250
Edelbrock Vortec Rerformer RPM aluminum intake with GM vortec gaskets $350
ALL NEW air conditioning, ompressor, ondenser, rings, reon etc. $700
New AC Delco Heavy Duty fan clutch $140
NEW Full Size radiator $120
new 200 amp alternator $250
Doug Thorley Tri Y headers Ceramic Coated and Magnaflow mufflers $600
Carb jetting, nd distributor curving, ull tune at performance shop $350

410 HP from GM, ..not some unknown machine shop.

TRANSMISSION:
Custom Built, igh performance, urbo 400 trans by The Toy Shop Transmission in Pomona, a. $1500 with new converter, ustom valve body and shift points, ill shift into first at any RPM for racing or mudding. Shifts very firm, ut not too hard to break, his meant that we had the valve body in and out of the transmission 5 or 6 times to get the firmness adjusted just right (quite an effort). Has heavy duty trans cooler $100. Also has B&M ratchet shifter $350 with reverse lock out.

TRANSFER CASE - Twin Stick:
NP 205 transfer case with all new bearings by Tri County Gear in Pomona, a. $800 rebuild with shift rod modification for twin stick operation. The NP 205 hardly ever needs a rebuild, hey are gear driven and VERY stout units. But, ou can't have a twin stick ability with out taking it apart to modify the shift rods. So new bearings were installed while it was disassembled for the TWIN STICK modification. This NP 205 has twin shifters to engage front or rear low transfer case individually or together $400. That means it can be front wheel drive. Or rear wheel drive in low transfer case, hich is how I do MOST of my mudding until I get stuck and engage the front axle to get out. It's a good practice and gives you a chance to get out on your own. And this truck flings more mud in 2 wheel drive than most trucks that use 4 wheel drive! No Joke. Hardly ever have I been stuck in this truck. But I have been stuck needing help.

DRIVE SHAFTS:
J.E. Reel in Pomona, a built the rear drive shaft with a NEW rear 1350 CV joint $450 and drive shaft tube with stock rear yoke and new u joints balanced $300. And all u joints on truck are new. The front drive shaft is also balanced with new u-joints in the CV Joint $300. Front CV Joint has been clearance all around the yokes so the yokes won't touch each other during harsh articulation angles. The front drive shaft angle is extreme, nd every trick has been done to ensure its proper operation. You'll be hard pressed to find another truck this BIG that has a front drive shaft connected, nd works, nd works correctly...

REAR AXLE:
Has 14 bolt semi float rear end with 30 spline axles, .5 inch ring gear, :88 gears $250 and a EATON Clutch Type Posi Carrier (it Does NOT have a stock eaton g80 - those always break) Posi cost $900 alone plus bearings etc.

FRONT AXLE & STEERING:
Front axle has 4:88 gears $170 and is an open carrier, o posi, ana 44 with an Off Road Unlimited cross over steering set up that cost over $1000 with new 2wd steering gear box needed for the conversion. I could have used a Dana 60, t would have been cheaper than the steering kit, ut I wanted the bullet proof, orged, piece, teering knuckle that is only made for the 44. Plus, left the differential open and have never broken an axle after lots of mudding. But, have broken several steering components on dana 60's axle housings in the past... Not to mention, he dana 60 has studs in the casting for the passenger side leaf spring pad threaded into the differential case that can (and have in the past) that can pull out! ...the dana 44 has U bolts that are stronger. And you can always look to see that dana 44 u bolts are tight vs. the dana 60 studs could be pulling out and you wouldn't know by looking. That's why I run a dana 44 and not a dana 60. Dana 60's can leave you stranded in the mountains with no steering, t has done that to me 3 times in the past, ll steering related problems. You'll never break the Forged ONE PIECE steering arm from Off Road Unlimited. One last point, he dana 44 axle that you might break is very cheap, 30 to replace if you break the stub axle vs. a dana 60 stub axle is $200. It's a cheap weak link to break.
Front axle steering knuckles were cut of and re-welded on with a proper pinion angle, sing a special jig to keep it all straight while welding, o let the front drive shaft work without breaking, nd that cost $1500 to have done and all new bearings and brakes were installed at that time costing even more in parts.

BRAKE LINES:
Custom Built, xtra Long, tainless Steel Braided brake lines front and back $200. Plus new Brake Master Cylinder $48, rake bias valve block $75 and rear proportional valve with adjustable hand knob from Wilwood brakes $42 for the back brakes adjustability, ew hard lines $35 etc.

LEAF SPRINGS:
Altlas custom leaf springs Front and Rear were bent for the truck and the front springs have a military wrap on them to keep the front from twisting and breaking the front drive shaft, hat cost extra and the military wrap works well at eliminating axle wrap in the front. $700
Rear springs have a shackle reversal and NO lift blocks (lift blocks are junk and break).
The Front springs are connected to a 4 x 6 rectangular tube with a receiver hitch for pulling out of mud. Works well and gives you the ability to hook to a truck in front and pull out a truck behind you like a train.

ROLL CAGE:
There is a custom bent roll cage in the cab built with 4130 chromoly tubing that cost $400 for the material alone! I spent lots of time bending the tubes just right to install it right up against the roof and rear cab.

CAB RE-BUILD:
The cab has dyno mat sound deadening material glued all over the bare cab when it was stripped bare and had nothing in the cab.
The upholstery was all new 6 years ago,
The front and rear glass and seal are brand new $700
The doors are completely rebuilt and have new seals, ew rubber, ew window motors and tracks and new door locks actuators and new switches and new everything like hinges and hinge springs and bushings etc. when I painted it this year. parts are $600
The truck was at the paint shop for 7 months and was completely taken apart including the doors and the bed was removed from the frame for $3500
It is a very clean and capable 3/4 ton 4x4 truck that can go mudding with the very best and mud better than most every truck. The axle gearing, ire diameter and engine rpm are all matched up to work perfectly together and they do work perfect.

39" TIRES & WHEELS:
The tires are new Super Swampers with 2000 miles on them, hey were "trued" which means I had Taffa, Big Rig Shop in Nashville, had Taffa's technicians make the tires round. So they put them on a machine that removes the high spot until the tires are round and drive smooth, his cost $400 to have the tires trued and balanced. Tires were $2150 delivered, he wheels are Micky Thompson 16.5 x 12 and cost $800. That is $3350 for wheels and tires trued and balanced for the street. All BIG mud tires are NOT round when new, nd they will bounce going down the road making you sick from vibration. These are smooth as silk, t the cost of precious rubber removed in the process and at the cost of several hundred dollars in expense to have it done. The truck goes down the freeway VERY NICE!

SHOCKS:
All shocks are 2 years old and are Rancho RS 5012 (rs5000 series), ll 10 of them. $600
5012 are 5000 shocks but longer than stock for the lift.
STEREO SYSTEM:
The stereo is an Eclipse with IPOD control, as two 12 inch Kicker sub-woofers. 1200 watts of power in a custom install with all the sound deadening material in the cab and it sounds absolutely wonderful, oud, lear, risp and hard hitting. Imaging is great with custom front speaker placement and Kenwood speakers with cross overs using capacitors (old school). Subs are electronically crossed over at the amp. System runs a Deep Cell Battery and 200 amp alternator. cost well over $1500 for parts alone.

THE TRUCK WILL DRIVE ANYWHERE IN COUNTRY RIGHT NOW,

AND PULL A TRAILER WITH IT.

IF I DON'T SELL IT, /p>

I WILL BE USING IT TO MOVE TO IDAHO FROM TENNESSEE PULLING A 30 FOOT TRAILER.

THANKS FOR LOOKING