1968 Chevrolet Corvette Stingray w/ all Original Parts Upgrades Frame Off Manual

Chevrolet Corvette 1968 Description

Fully loaded and documented

1968 Corvette, 427 Tri-power # matching roadster 4 speed Updated Race Car
You are buying two packages with one deal- what can be better!

My late husband bought this Vette in the late 1980’s and spent five years doing a frame-off restoration (picture albums included in the sale) to the full Bloomington Gold standards. Not a detail was overlooked and it won numerous awards at various car shows. Then, in the late 1990’s either his youth spent racing cars in southern California or his need to tinker (former Professor of Mechanical Engineer at Villanova University) took hold. The original motor, seats, wheels & tires were all removed.

THIS MEANS it can be “restored” to its original condition when it came off the showroom floor with it's 427 BIG BLOCK, 390 HP 4-speed or sell the parts or sell the parts etc for a profit. (They are labeled and numbered) The original block, heads, and complete engine with a factory correct tri-power setup including intake, carbs, air cleaner, etc. is available along scads of other parts too numerous to mention and instruction manuals. Keep in mind, in 1968, the first year for the C3 generation, this is one of the 18,630 roadsters built.

On the car that is shown and modified – the following is on the car.

1968FIRST YEAR OF THE MAKO SHARK II

(1965 GM Show-Car) DESIGN

Present TRACK CAR for road courses

SPECIFICATIONS:

COLOR : VIPER RED from Dodge (sorry G.M.),

HOOD: L88 style, Black Hood Stripes from LT-1 Vette, Aftermarket Front Air-splitter

TOP: REMOVABLE HARDTOP

Removable HARDTOP USED BY FACTORY L88 RACING VEHICLES SINCE TOP SPEED WAS ABOUT 10 MPH HIGHER THAN THE T-TOPS DUE TO LESS DRAG

ENGINE: G.M.'S 502 cu. in., Street Solid Roller Cam by COMP Cams, dual pattern

0.676 lift with Howard Cams 1.8 ratio lifters

Crower HD mechanical roller lifters, Crane Cams 3/8 Cromemoly push rods,

950-cfm QuickFuel Carb,

MSD Digital Controls, Red-lined set at 7100 RPM

Trick Flow single valve springs, Titanium Retainers.

Holley RPM Performance aluminum heads, 2.30 int., 1.90 exh. SS competition valves, port-matched to Holly RPM Dual Plane manifold,

2.0 inch HOOKER Super Competition Headers, ceramic coated

3.0 inch collectors into 3.0 exhaust system, H-pipe, stepped down for 2 ½ TURBO mufflers + stock SS exhaust tips (with bungs for Wide range oxygen sensors)

125HP Holley NOS plate, with NOS digital controller, RPM window 2,800-7000

DRIVE TRAIN: O.E.M. Muncie M22 ROCK CRUSHER gear set inside M21 casing

SFI approved Steel Bell Housing

SPEC Stage 3+ Clutch

3.08 Positraction Rear-End from 1972 Vette

Gear Vendors Overdrive Unit

Chrome Moly Driveshaft and Half-shafts, Driveshaft Hoop

SUSPENSION: Polyurethane Bushing Everywhere

Adjustable Transverse Fiberglass Single Leaf Suspension, front and rear,by VBP Suspensions

Belstein SPORT shock-absorbers (similar to C7's Z51 package)

VBP Smart Struts in rear

1 3/16 front roll bar matched to 3/4 rear roll bar, with adjustable end-links

Front wheel spindles from 1969 Vette – 50% stronger that the 1968's

Vehicle lowered via adjustable links on Springs to Height of 48 inch.

Weight distribution is 51% front, 49% rear

BRAKES: Front: 2-piece Wilwood Alum Hat - Steel Rotor, 14 inch dia.

6p calipers in front, 4p calipers in rear

Rear: 2-piece Wilwood Alum Hat - Steel Rotor, 14 inch dia.

MOTUL 600 Racing brake fluid

O.E.M. Power Brakes

WHEELS/TIRES: front = 18 X 8 inch, aluminum rims with Michelin Pilot Super Spor, 245/40 tires

Rear = 20 X 9 inch, aluminum rims with Michelin Pilot Super Sport 275/35 tires

This combination gives the desired “rake” for aerodynamics.

SAFETY EQUIPMENT: POWERMETRIC 5 – Point Roll Bar, approved SCCA design with diagonal bar, were as NHRA requires horizontal bar

5 – Point Safety Harness, SKI approved Roll – Bar Padding, SFI approved - 2-Layer, Fire Suit Size M

Contour/Booster Seats from CORBEAU

He drove this car on race tracks around the country (CA, AZ, VA, NY, DE, NJ, FL & others). It’s unbelievably fast and sticks like glue to the road (just check out those tires). It has never been in an accident and is super clean - he cleaned it with Q-tips!!! It kept him busy hours a day and was his pride and joy. I am keeping his race helmet as my daily reminder of him, but the car in its current form and all the parts for the original vehicle must go as a bundle. The car itself was professionally appraised at $55, 000. Asking price for the WHOLE bundle is $45,900.00

This Corvette Stingray is a must see and drive.

Don't miss the opportunity to own this beautiful car!

402-502-8386