1965 Shelby Cobra Factory Five custom built perfect condition Fuel Injected
- Price: Ask a price!
- Condition: Used
- Item location: Longview, Texas, United States
- Make: Ford
- Model: Shelby Cobra
- Type: Convertible
- Year: 1965
- Mileage: 1,711
- Color: Blue
- Engine size: 410W by Keith Craft
- Number of cylinders: 8
- Fuel: Gasoline
- Transmission: Manual
- Drive type: RWD
- Interior color: Black
- Options: Leather Seats
- Vehicle Title: Clear
Ford Shelby Cobra 1965 Description
This car is located in Longview, TX and is a one owner car with a clear TX title. It is inperfect condition in every way. It runs 0 to 60 in 1.9 seconds and just under 10 second quarter mile. It comes with Cobra wheels and tires and an extra rear set of cobra wheels and drag slicks. It was hand built to perfection and I do have allreceipts of everything done to the car. Below is a quick list of details on the car.Engine:
410W built by Keith Craft
Forged 4340 crank and rods
2618 Pistons
11:1 Compression
Steel girdle
TFR R-Series Heads
-Intake ports raised 1/2"
-2.10"In/ 1.60"Ex.
-Titanium retainers
-Flow IN:354@.700 & EX:257@.700
-Crane gold rockers
Matched Super Victor intake w/ raised ports
Comp Cams hyd. roller .613/.644
SFI Balancer & Flywheel
All ARP Hardware
Transmission:
TKO 600 w/ .64 OD
Spec Stage 3+ Clutch/pressure plate
New Shortened driveshaft w/ all Spicer parts
Rearend:
8.8" Fox width
Motorsport 3.55:1 gears
Hardened axles
Carbon Clutches
2.5" long Studs
Suspension:
Front FFR tubular lowers - Pin Drive Width
FFR Adjustable Uppers
Pro Shocks Coil-overs
'01 Cobra spindles
Rear Custom 3-link w/ upper link centered over 3rd member
Adjustable tubular lower control arms
Adjustable tubular upper control arm
Adjustable QA1 Coil overs
Competition Engineering Anti-roll bar
Brakes:
Front - 13" Cobra
Rear - 11.7" Cobra
Custom braided stainless flex lines F&R
1/4" polished stainless hard line w/ stainless aeroquip fitings
'01 Cobra Master cylinder
Cooling:
NASCAR 19"x31" DUAL PASS radiator- HUGE
Custom 1 7/8" hard plumbing
'03 Cobra Cooling fan w/ custom mounts on radiator
Earl's polished aluminum thermostat housing
CSR aluminum filler neck
Polished aluminum filler cap
Polished Edelbrock water pump
Polished March underdrive pulleys
Adjustable fan controller w/ over-ride switch
Electrical:
Painless wiring harness and switches
Polished 200A 3G alternator
Pro Tork mini starter
MSD digital 6
MSD blaster coil
MSD billet bistributor
Aeromotive fuel pump controller
Optima Battery
Large 2-O battery cable
All ground studs welded to frame for good contact
All lighting has quick disconnect plugs
Exhaust:
Custom 1 7/8" ceramic coated headers
Ceramic coated sidepipes
O2 bungs welded for wideband O2
Exterior:
Original style finned aluminum side vents
Original style Cobra front and nose badges
Original style 427 side badges
Polished roll bar bezels
Original style Cobra steering wheel insert
Driver and Passenger side mirrors
Original style wind wings and visors
Chromed quick jack bumpers
Front quick jack grommets
Stainless body washers w/ rubber backing
Door and hood rubber D-molding
Polished fuel filler neck w/ built in locking gas cap
Lucas Clear front parking light lenses
Shelby Motors License plate frame
Polished billet windshield frame bezels
Frame Mods:
Rear frame narrowed to accept 13" rim
Dual ceramic coated roll bars
Battery tray over fuel tank for trunk access
Front Coil over brackets shortened
Front UCA mounting slots filled
Removable steel tube to hard mount radiator
Rear coil over backets mounted inside frame
Curved upper trunk support tube like MKIII
Lowered trunk aluminum for additional room
MKIII hood hinge w/ custom plates bonded on hood
MKIII door hinges
Frame extended to support lower dash
Fuel:
Billet fuel pump
Billet -10AN fuel filter
Braided stainless -10AN fuel line
-10AN in-tank pickup
Race Holley fuel regulator (12-704)
DC Carbs 950 cfm billet carb
Polished billet ball-milled oval aluminum air filter
Polished throttle cable bracket
Braided stainless throttle cable
Interior:
Autometer Cobra style gauges w/ reverse speedo
Adjustable driver seat
Raised passenger seat to match driver
A/C aluminum pedals for all pedals
Stainless cup holders
Driver side Simpson harness upgraded to cam lock style
Polished seat belt bezels
Steering:
Ididit polished aluminum steering column
Integral self canceling turn signals
Polished stainless steering U-Joints
Custon polished stainless steering shaft
Ididit polished aluminum lower ball mount
Flaming river manual rack
Flaming river outer tie rods
Wheels/Tires:
PS Engineering Hallibrand wheels
17" x 8" Frotn & 17" x 9.5" Rear
M/T 26 x 11.5 ET Streets