1965 Dodge Dart Charger Dealer Kit Car 273 V8 273 Hi Performance x 4 BBL 4 spd

Dodge Dart 1965 Description

1965 Dodge Dart Charger Dealer Kit Car with 273 V8 273 Hi Performance x 4 BBL 4 speed stick.

In November 1964 Dodge launched the Dart Charger. 480 Dart Chargers were produced, 180 of which were built at the plant, while parts for an additional 300 “Dealer Kits” were produced and shipped to Dodge dealers in 11 western states.Dealers could put these Kits on any 273 Hi Performance cars they had in stock. This car is 1 of 36 remaining (from the original 480 produced) Dart Chargers known in existence today.It has been authenticated and listed in the International 1965 Dodge Dart Charger Registry.Documentation provided.

Original 273 cu. in. Hi Performance engine and transmission with a rebuilt on engine and approx. 45K miles.The 273 Hi Performance engine came with a Carter 4-barrel carburetor (rebuilt), 10.5:1 compression, a more aggressive camshaft with solid tappets, and other upgrades which increased output to 235 bhp (175 kW). Four speed transmission with stock Hurst shifter and original knob.

Numbers match. It has the Charger air filter, alum valve covers, 10" drum brakes (Frt10x 2.25”, rear 10 x 1.75”).The original color was cream yellow.It had been repainted, at one time to a black with a “gasoline-like iridescence” in the clear coat on top the paint and has the insignias of the Elks Lodge that raced it, 1/4 mile stock.The original hardtop was covered in black vinyl, the vinyl is gone and the metal is painted with a low-quality white paint.Interior has been completely restored with the addition of pockets on the back side of the front seats. The interior is missing one seat rear button, I have the original Masonite speaker plate for the rear that can be used for templating.All exterior trim is on car (with exception of drivers side rear wheel well trim which I have and is included), red white and blue paint on emblems is faded off as is black paint on hood.Left front fender looks to have bodywork done on it. Undercarriage, floor pans, and trunk floor are solid, only tiny amounts of surface rust.Interior floor has been treated with Rustmort to neutralize light surface rust where needed, sound proof matting lines floor under new carpet and roof under new headliner.It has rust through on drivers rear fender and a 1” patch of rust on passenger side rear fender.This is from isolated areas of pine needles that collected up in the wheel well.I have the replacement stampings for the drivers side and they are included with the car.Passenger side rear corner has a dent in it, included is a rt rear corner from a ’66.

Upgrades and restos (since 2003):

ENGINE: (rebuilt by previous owner, has approx 45,000 mi on it)

Alum. 2 core radiator

Mopar Electronic ignition (Dist, module, and voltage regulator, ignition coil)

Dual field electric/charging system - Powermaster Alternator

7 blade fan w/clutch

MSD Super Conductor spark plug wires

New thermostat and gasket

New fuel pump

New water pump

Rebuilt stock Carter 4 BBL carburetor

Freeze plug petcock

BODY/INTERIOR/BRAKES/ELECTRICAL:

New restoration front bucket seat upholstery

Resewn original back seats

New restoration Headliner – Black perforated

New restoration visors – Black perforated

New restoration black carpet

New manual brake and clutch pedal pads

Mr Gastket marine battery box, in truck over rear wheels w/ Summit Racing kill switch

Sport Comp silver 3” Tachometer

2.5" dual exhaust w/ crossover

(2) Flowtech Afterburner mufflers

(2) Firebird chrome square exhaust tips

New custom accelerator cable

New custom emergency brake cable

Addco rear sway bar w/ polyurethane bushings

New rear axle seals

New rear axle bearings

New front and rear brake shoes

Turned and finished rear drums

New brake master cylinder

Rebuilt brake slave cylinders

New front brake flex hoses

New ignition switch

New lug nuts and washers

Milled custom aluminum gas cap

’66 truck lid

Included but not yet applied:

New Left side rear wheel well metal stamping patch

New Left side rear quarter panel metal stamping patch

On May-06-16 at 21:20:31 PDT, seller added the following information: