1967 GMC 1/2 ton shortbed fleetside conversion

GMC Other 1967 Description

*** Please read the entire ad and ask all your questions before making your bids - Sale is "AS-AS and final" ***
This is a great truck! Very desirable 67 GMC with small back window.
Original paint and patina
Very strait body.
TRUCK:
-1967 GMC small back window cab
1/2 ton Short-bed fleet side converted from 3/4 ton long bed
-1970 1/2 ton Chevy chassis - shortened (chevy chassis is coil over rear VS leaf spring - also desirable as its easy to bag and lower)
-3/4 lowering kit with shocks
-all new steering and suspension
-1967 327sbc with Camel hump heads - has been rebuilt once as evidenced by the rods being stamped with cylinder numbers
-Saturday night special camshaft
-Aluminum dual plane intake
-holley 750 double pumper
-NP435-GA four speed transmission with new clutch and surfaced flywheel
-stainless shorty headers
-all new interior
-all new wiring harness
-patch panels are90% done
-strait body
-12-bolt posi rear-end with 4.10 gears
-chassis was blasted to bare metal and sprayed in three heavy coats of rustolium satin black with a spray gun
FRAME:
Was originally a 3/4 ton long bed (still titled that way)
Purchased a 1970 1/2 ton long bed frame and shortened it.
Z-notch was done the right way, under the cab.
Cuts were made with a plasma cutter and a jig.
Center-line of z-notch was cut 16" forward of rear cab mount.
Mated front and rear half, tac-welded, cross checked welded and rechecked measurements to ensure frame did not twist or contort while welding
Frame was reattached, front half to back half by welding both the inside and outside of notch cuts and finish sanded on outside of frame rails
Fish plate welded to inside of frame rails.
Frame, suspension and rear-end was bead blasted to bare metal and painted in three full coats of Rustolium Satin Black #7777 from a gun
BED:
Original long bed was cut using a plasma cutter and jig.
Forward cut was made 12" back from front of bed and 12" was removed from that point moving towards the wheel well
Rear cut was made after wheel well, 8" was removed.
bed floor was notched forward and rearward allowing the rear tailgate section and bed sections, and the font panel and bed sections to be reunited and appear continuous
More welding will need to be done to complete the task but the hard part is done
CAB AND FRONT CLIP:
Both left and right inner and outer rocker panels have been cut out and replaced
Drivers side floorboard has been cut out from rocker to transmission tunnel and replaced
Partial passenger floorboard replacement done from passenger rocker to about 10" in towards tranny tunnel
Both door bottoms have been cut out, Drivers door bottom replacement has been cut to fit, passenger door bottom replacement still needs to be cut to fit
Original dash was rusted out at drivers side at the window channel, it was removed and a clean rust free original takeout dash was purchased
There is still a little rust repair to do at the footwells, but it is minor or not necessary depending on how you want the interior to look
Firewall is in great shape as are inner fenders, fenders and grill. Radiator core support is mostly great accept under battery tray - i was ok with it.
All glass is in great shape but front windshield was damaged and removed
Plans were:
short bed conversion
detail engine and entire chassis
redo the soft interior (was undecided about the hard surfaces but had started sanding the metal and considered repainting in original color)
Scuff exterior and clear in satin, same with entire engine compartment
Paint entire underside and inside of bed with tint-able U-POL Raptor Liner tinted to match original blue exterior color
3/4 drop
PURCHASED FOR THE TRUCK AND COMES WITH IT:
Seat cover
Carpet
Dash pad
Door lock pulls
All new interior door handles
New window felts
New door rubbers
New front windshield rubber
New aluminum radiator
New heater core
New heater blower motor
All new steering components accept manual steering box is original as well as column
New motor mounts
New fuel pump
New water pump
Custom made alternator bracket
New hotrod wiring harness for entire truck
16" Black steel wheels - 10 hole (came with 1/2 ton chassis that was purchased)
WHAT WILL BE NEEDED TO FINISH THE TRUCK:
-front windshield
-rear window weather stripping
-alternator
-driveshaft needs to be shortened
-Radiator hoses
-Soft brake hoses
-Fluids
-Clear coat - satin
-U-POL Raptor Liner
-Exhaust from the headers back
We were hit with our winter snow before i could snap pictures of the bed, i will work on getting them up or email me to get pictures of anything you would like to see.
Cab and bed can be put back on the chassis at buyers choice / request